Pixhawk PRO is a simple flight control + shock absorber + mount + M8N GPS + power supply module

Name: Pixhawk PRO is a simple flight control + shock absorber + mount + M8N GPS + power supply module
Brand: B-CUBE
Price: 117.03 USD
Availability: InStock

Pixhawk PRO is a simple flight control + shock absorber + mount + M8N GPS + power supply module

$117.03за шт.

Варианты

КоличествоJane with a meal.

Ваш заказ

$117.03 за шт.

1 штукаJane with a meal.

Взвешиваем упаковку…0 s

Оплата от 100 шт. или от ⁦$1,000⁩ за товары

Стоимость доставки указана ориентировочно. Окончательная сумма определяется по фактическому весу посылки и выставляется позже.

Покупки с soorce

Офис в АлжиреКоманда на месте ответит на вопросы и сопроводит заказ.

Проверка по запросуПроверяем ваши товары на нашем складе перед отправкой.

Товар оплачивается при заказеДоставка выставляется позже, по реальному весу посылки.

Отслеживание до двериКаждый этап виден в ваших заказах.

Есть вопросы? Напишите нам

Поставщик

Фабрика в КитаеОтвечает в течение 1–2 рабочих дней

1732170672
PIXHAWK PRO

Features:

Pixhawk PRO support the latest official ardupilot firmware and PX4 firmware.

1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;

2. 14 PWM / servo output;

3. Bus interface (UART, I2C, SPI, CAN);

4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;

5. Provide automatic and manual modes;

6. Provide redundant power input and failover;

7. Multicolor LED lights;

8. Provide multi-tone buzzer Interface

9. Micro SD recording flight data;

10.TYPE-C USB port

11.GH1.25 port

Specifications:

Interface

1.5 high voltage compatible UART 1, 2 with hardware flow control

2. 2 CAN

3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input

4.Futaba SBUS compatible inputs and outputs

5.PPM Signal Input

6.RSSI (PWM or voltage) Input

7.I2C

8.SPI

9.3.3 and 6.6VADC input

10. External MICRO USB Interface

Package include:

PIXHAWK PRO x1

Safety Button And Buzzer X1

3Line (4P GH1.25, 6P GH1.25, 2.54Pin )

M8N GPS X1

GPS Holder X1

3DR Power Module X1

Shock Absorber X1

For PIXHAWK 2.4.8 :used for PIXHAWK2.4.8 AND APM2.8 Flight Control
For PIXHAWK PRO :used for PIXHAWK PRO Flight Control
For PIXHAWK 6C :used for PIXHAWK 6C Flight Control

Description:
This Power Module PRO provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.
Specification:
Input Voltage: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max Current Sensing: 120A
Output: DC 5.2V & 3A Max
Voltage Divider: 18.182
Amperes per Volt: 36.364
Weight: 20g
Please Note:
The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference.

M8N GPS: